A personalised stand measured for the bowl
you already own.

You pick one of six sizes — 11, 13 and 15 cm, plus three measured steel bowls: 135, 160 and 205 mm across the rim. If your bowl is different, choose “My own bowl” under “Bowl size” and enter three measurements taken with calipers (rim, body, depth): the stand is calculated for exactly that bowl, at no extra cost. Not sure? Print the free fit check first.

Yes, for free — no order needed. Under “Bowl size”, tap “Not sure it fits? Download a free fit check”. It is a thin slice of your stand, cut exactly where the bowl sits: the top of the stand with the rim seat and the opening — the two places where a bowl either fits or does not. It prints in a fraction of the time of the whole stand. Drop your bowl in: if it sits flush, the whole stand will too. It is only for checking the bowl: the rail, wall pattern and colours are left out on purpose — your full stand will have them. The slice cannot check depth, so with your own bowl, measure it carefully. The size is engraved underneath: a size from the list (for example DOG 15 or STEEL 160), or your own measurements as rim/body/depth in mm, followed by S and a number if you changed the shelf under the rim. The shop remembers the size you tested, so when you come back, “Use this size” sets it again. Files-only orders that include a stand get the fit check once more, with the end of your order number on it.

Like the stand: lay it flat exactly as it comes in the file, with no supports, and print it in the same filament and with the same settings you will use for the stand — PETG, 0.2 mm layer. That way the slice also checks your printer: if holes come out slightly tight on your machine, you see it here, not on the whole stand. It prints in one colour, so the AMS slots do not matter.

First look underneath: the engraving tells you which size the slice was made for. If the bowl will not go in or has to be forced, choose a larger size from the list — or, with “My own bowl”, measure the rim again at its widest point. If it rattles or sits too low, choose a smaller size or measure the rim and body again. If it rocks or the rim barely rests on the edge, raise “Shelf under the rim” under “My own bowl” (the default is 4 mm). After any change, download a new fit check — it is free — and print it again. If you print the files yourself and the slice is tight although your measurements are right, your printer probably prints holes slightly small: check the hole or XY compensation in your slicer, because the whole stand would come out the same way.

Measure before you order. The sizes in the list refer to the rim: 11, 13 and 15 cm mean a rim up to that width, and the three steel sizes are measured across the rim. Measure your bowl across the rim at its widest point and compare. If it falls between sizes or the bowl is unusual, choose “My own bowl” and enter the rim, body and depth measured with calipers — two millimetres off can mean a bowl that will not go in or rattles. Each stand is made to your settings, so check the numbers twice before you pay. The surest option is to add a metal bowl to a printed stand or set: it comes in the size of the stand. Still unsure? Write to us with the measurements and a photo of the bowl.

Yes, with a printed stand or set: tick “Add a metal bowl” when you order. It is a metal bowl in the size that matches the stand — 11 cm $2, 13 cm $4, 15 cm $6, 135 mm $4, 160 mm $6, 205 mm $8. It is not offered with a custom-measured bowl, because then you already have yours.

The food sits in a metal bowl — the print never touches it. The stand, the name plate and the lid hold the bowl and have no contact with food. PETG washes well and does not go brittle, but we do not claim food-contact compliance for it, and there is no need to.

You can, but know what you give up. PLA softens in hot water and can warp when washed, it is brittle on impact and handles damp poorly. For something that stands on the floor and gets washed, PETG is the right choice.

Slicer-ready files with colours as AMS slot numbers. That means the filament sitting in that slot is what prints — not a colour stored in the file. One file per part; print them separately. Each part uses the slot numbers you set in the configurator: by default the body is slot 1 and the letters slot 2, and two-colour stands and lids use up to four slots. In Bambu Studio and OrcaSlicer the slots load by themselves: just check that each slot holds the filament you want; if not, swap the spools or change the assignment in the slicer in two clicks. In other slicers the bodies are separate too, you only assign the numbers yourself. With a single-nozzle printer everything prints in one colour and there is nothing to set up. Engraved mark: the files carry a small RowLab3D mark and the end of your order number, on surfaces you do not see once the stand is assembled — inside the lid, in the rail channel, under the stand and on the name plate's slider.

We do — every order is printed by us, in our own workshop in Poland, not passed on to an outside print farm. Every design in the gallery is sliced and checked before it goes online, on the same printer that makes your order: a multi-colour printer with an automatic filament changer (Bambu Lab P1S with AMS). Bambu Lab is a trademark of its owner. RowLab3D is not affiliated with Bambu Lab.

Each part of the name plate has its own slot number in the configurator: the plate and its slider print from the “name plate” slot, the outline (if you turn it on) from the “outline” slot, and the letters and the icon from their own slots. By default that is plate 1, letters 2, icon 2 and outline 3. The numbers you set go into the name plate's 3MF file, just as they do for the stand and the lid.

So that it fits. In a full set the lid takes the shape and wall pattern of your stand — it continues the stand's wall. From the lid pattern you pick you get its colour, and its outline or name if it has one.

“Change more” opens the full configurator. Once the preview there shows your changes, tap “← back to shop”: the shop comes back with the version you built, ready to buy, and fills in its slots, colours, name and icon for you. If you buy straight away, you get exactly that version. If you change something in the shop first, the stand is rebuilt from the shop's own fields, so anything the shop has no field for — a second line of text, text on another wall, other advanced settings — is dropped. To keep those, make all your changes in the full configurator and buy right after you come back.

Yes. Every printed order includes the 3MF files. If a part ever breaks, you reprint that one part instead of ordering the whole thing again.

Five times per file, from your order page — the link is in your order e-mail, and you need the e-mail address you ordered with. Every visit to that page gives fresh download links. The fit check does not count towards the limit. If you run out, write to us and we will unlock them: your configuration is stored, so the files can always be rebuilt.

Yes. Open your order page (the link in your order e-mail) and, at the bottom, under “Buy a part for a stand you already own”, enter the e-mail you ordered with. We send you a link to your stands, valid for 24 hours. Pick a stand and tap “Use this stand”: the configurator starts from your original order — same size and look — and you choose the part to change or buy. Change the text, colours, wall or rail, or nothing at all. Picking a different pattern starts a new look that still fits that stand.

Printed sets: Poland from $5 (InPost parcel locker), EU countries from $18 (DPD); USA — soon. The exact amount for your country is added before payment. 3MF files: worldwide, by e-mail right after payment, with no shipping cost. Several prints in one order: the number of parcels depends on the size and weight of the prints, and shipping is the country price × the number of parcels — the basket shows it before payment.

See shipping prices for every country

Files: a few minutes after payment. Prints: usually up to 10 working days to make, then 1–5 working days in transit depending on the country. You get the tracking number by e-mail.

• PETG — hand wash, or dishwasher at low temperature
• The print has no contact with food
• Bowl: metal
• Do not leave your pet unattended while feeding

A print is made to your configuration, so it cannot be returned just because you changed your mind — the text is built into the body. If a print is faulty or differs from what you ordered, write to us with a photo: we replace the part or refund you and pay for sending it back. An added metal bowl can be returned within 14 days. For digital files the right of withdrawal ends once the download starts, which you are told before you pay.